THE ALL NEW, ALL STAINLESS STEEL “S” SERIES VIPER SUBMERSIBLE WINCH IS SHIPPING!
“The First 316 Stainless Steel Marine Gearbox on a Drum Anchor Winch in Australia”
The Viper “S” Series RAPID has set new standards in anchoring systems. The new Viper 1000W electric motor (hand polished marine 316 grade stainless steel) has made it one of best selling anchor winch in Australia. With a fall rate of over 50 meters per minute and a retrieval rate of 45 meters per minute the Viper will ensure you get onto your GPS mark, first time, every time!
- Now includes an Emergency Manual Release Safety Feature. This feature enables you to deploy your anchor if your boat has lost all power and is heading for a cliff, sand bank or a bar crossing, you can lower your anchor without power. Making sure you can safely anchor your boat avoiding dangerous drifting into a hazardous location. The winch will allow the anchor to release to the seabed. Once the anchor is on the bottom, tie your rope to a bollard to be safely anchored. Then you can call the coast guard or your local emergency marine service.
- With unsurpassed Viper reliability, it has more torque than a conventional drum winch, 3 support bearings hugging a 28mm one (1) piece solid shaft and a 90 degree welded housing bracket which closes up the gap between your drum (preventing rope jams) and does not require any additional guards.
- With a life time warranty against water intrusion, and a bullet proof 5-year Viper performance warranty, you can’t go past a Viper. Now supplied with everything you need to install it, including a 5mm stainless steel sandwich plate, all required stainless steel bolts/screws/nylocs/washers, 2 face plates depending on your dash space and even your rope chain and even swivel are included.
- All you have to add is your own cabling or one of our factory made Bell Marine tinned copper marine wiring looms, you will never have to break your back pulling up your anchor and chain again!
- Including 200mtrs HiSpec UHMWPE Rope, Pre-Spliced to a 10mtr 8mm 3 Strand Shock Cord & Is Attached Via A S/S Shackle to 8mtrs of 6mm Gal Short Link Anchor Chain Kit
Please Note: 3B&S cables are already attached to our motor and leak tested to a IP68 Rating.
Specifications:
- 1000 Watt Stainless Steel Submersible Electric Motor with IP68 Certifification
- All New 316 Stainless Steel Marine Grade Worm Drive Gearbox
- 28mm Solid S/S Shaft With 3 Support Bearings
- 8mm Marine Grade 316 Plate S/S Hand Polished to a Mirror Finish
- 360 Degree Motor Rotation 16 Different Positions
- 1 Mtr of 3 B&S Tinned Copper Cable Fitted & Leak tested
Note: Download the Pro Series II 1000 Wiring Diagram for more information
Note: Download the Pro Series II 1000 Tech Drawings for more information
| Part Number | Max. Fall Rate | Max. Retrieval Rate | Suit Vessel Length | Weight | Well Clearance Required (W x D x H) |
|---|---|---|---|---|---|
| VIP-30021-5S | 50m per minute | 45m per minute | 5.7m + | 17kgs (winch only) | 395mm x 410mm x 260mm |
Includes:
- VIP-30021 - Viper "S" Series All Stainless 1000 submersible anchor winch supplied with 1 mtr 3 b&s power leads & joining connectors pressure tested & sealed
- VIP-30027 - 200mtrs Of 5mm 12 Plait Uhmwpe Hi Spec 3000 Rope & Chain Kit- 2050kg B/Strain
- VIP-30001 - Viper pro series anchor swivel - small
- VIP-30009 - Viper deluxe anchor roller - small
- VIP-30020 - 200amp reversing solenoid
- VIP-90021 - LED illuminated marine rocker switch
- VIP-90046 - Viper laser etched led illuminated switch cover
- VIP-30046 - 100 amp flush mount circuit breaker with rubber seal
- VIP-30051 - Single LED switch stainless steel face plate
- VIP-30052 - Combo LED switch & circuit breaker S/S face plate
- 5mm stainless steel sandwich plate
- All fixing hardware
- Installation notes & wiring diagram
